Terms and conditions apply.

E6 Optical Kit Encoder

Please see the EM1 Component Change Notice.
4 / 4
  • e6_webproduct_02.jpg
  • e6_webproduct_03.jpg
  • e6_webproduct_04.jpg
  • e6_webproduct_01.jpg

Overview

  • Quick, simple assembly and disassembly
  • Rugged screw-together housing
  • Positive finger-latching connector
  • Accepts .010" axial shaft play
  • Tracks from 0 to 300,000 cycles/sec
  • 64 - 2500 CPR | 256 - 10,000 PPR
  • 2 channel quadrature TTL squarewave outputs
  • Optional index (3rd channel)
  • -40 to +100C operating temperature
  • Fits shaft diameters from 2mm to 1"

The E6 Series rotary encoder has a molded polycarbonate which utilizes either a 5-pin or 10-pin finger-latching connector. This optical incremental encoder is designed to easily mount to and dismount...

Read more

Product Specifications

ParameterValueUnits
Operating Temperature -40 to 100 C
Vibration (5Hz to 2kHz) 20 G
Electrostatic Discharge, Human Body Model ± 4 kV

 

ParameterDimensionUnits
Max. Shaft Axial Play ±0.010 in.
Max. Shaft Eccentricity Plus Radial Play (1) 0.004 in.
Max. Acceleration 250000 rad/sec²
Max. RPM (2)
e.x. CPR=2500, max. rpm=7200
e.x. CPR=100, max. rpm=60000		 minimum value of ((18 x 10^6) / CPR) and (60000) rpm
Typical Product Weight
Single-ended (S-option)
Differential (D-option, L-option)
1.55
1.83
oz.
Codewheel Moment of Inertia 8.9 x 10^-5 for bore < 12mm
4.0 x 10^-4 for bore ≥ 12 mm		 oz-in-s²
Hub Set Screw #3-48 or #4-48  
Hex Wrench Size 0.050 in.
Encoder Base Plate Thickness 0.135 in.
3 Mounting Screw Size #0-80  
2 Mounting screw size #2-56 or #4-40  
3 Screw Bolt Circle Diameter (3) 0.823 ± 0.005 in.
2 Screw Bolt Circle Diameter 0.750 ± 0.005 in.
Required Shaft Length (4)
  With E-option (3)
  With H-option		 0.445 to 0.570
0.445 to 0.750
> 0.445		 in.
Index alignment to hub set screw 180 ± 5 mechanical degrees
Technical Bulletin TB1001 - Shaft and Bore Tolerances Download

(1)  Position inaccuracy is proportional to shaft radial play.

(2) 60000 rpm is the maximum rpm due to mechanical considerations. The maximum rpm due to the module's 300kHz maximum count frequency is (18 x 10^6) / CPR.

(3) Only for shaft diameters < 0.472".

(4) Add 0.125" to all required shaft lengths when using M-option.

ParameterTorque
Hub Set Screw to Shaft 2-3 in-lbs
Cover (4-40 screws through cover into base) 2-4 in-lbs
Base to Mounting Surface 4-6 in-lbs
Base to Mounting Adapter Plate 4-6 in-lbs
Adapter Plate to Mounting Surface 4-6 in-lbs
Module to Base 3.5-4 in-lbs

A leads B for clockwise shaft rotation, and B leads A for counterclockwise rotation viewed from the cover/label side of the encoder.

  • Specifications apply over entire operating temperature range.
  • Typical values are specified at Vcc = 5.0Vdc and 25°C.
  • For complete details, see the EM1 product page.
ParameterMin.Typ.Max.UnitsConditions
Supply Voltage 4.5  5.0 5.5 V  
Supply Current   27 33 mA CPR < 1000, no load 
  50 62 mA CPR ≥ 1000, no load
Low-level Output     0.5 V IOL = 8mA max.
High-level Output 2.0     V IOH = -8mA max.
4.2 4.8   V no load
Output Current Per Channel -8   8 mA
Output Rise Time   110   nS  
Output Fall Time   35   nS  
  • Specifications apply over entire operating temperature range.
  • Typical values are specified at Vcc = 5.0Vdc and 25°C.
  • For complete details, see the EM1 product page.
ParameterMin.Typ.Max.UnitsConditions
Supply Voltage 4.5 5.0 5.5 V
Supply Current   29 36 mA CPR < 1000, no load 
  57 65 mA CPR ≥ 1000, no load
Low-level Output   0.2 0.4 V IOL = 20mA max.
High-level Output 2.4 3.4   V IOH = -20mA max.
Differential Output Rise/Fall Time     15  nS  
5-pin Single-ended (1)10-pin Differential, Standard (2)10-pin Differential (L-option) (2)10-pin Single-ended (A-option) (2)
PinDescriptionPinDescriptionPinDescriptionPinDescription
1 Ground 1 Ground 1 No connection 1 A channel
2 Index 2 Ground 2 +5VDC power 2 +5VDC power
3 A channel 3 Index- 3 Ground 3 Ground
4 +5VDC power 4 Index+ 4 No connection 4 No connection
5 B channel 5 A- channel 5 A- channel 5 No connection
    6 A+ channel 6 A+ channel 6 Ground
    7 +5VDC power 7 B- channel 7 +5VDC power
    8 +5VDC power 8 B+ channel 8 B+ channel
    9 B- channel 9 Index- 9 +5VDC power
    10 B+ channel 10 Index+ 10 Index

(1) 5-pin single ended mating connector is CON-FC5.
(2) 10-pin differential mating connector is CON-FC10.

Index

Provides a single pulse per revolution.

3-option

3-option makes all five of these hole diameters .125".

View option:

S-3-option_1.jpg

D-3option.jpg

E-option

The E-option provides a cylindrical extention to the cover allowing for longer shafts of up to .750".

Please note: Only available for shaft diameters <.472".

View option:

E6S-Eoption_0.jpg

E6D-Eoption_0.jpg

H-option

The H-option adds a hole to the cover for the shaft to pass through.

  • Shafts 2mm to 10mm, a .438" diameter hole is supplied.
  • Shafts 12mm to 1", a 1.047" diameter hole is supplied.
View option:

S-H-option_0.jpg

D-H-option_0.jpg

L-option

Provides Avago / Agilent / HP differential compatible pin-out. See direct replacement information above.

Please note: Only available for E6D and E6MD (10-pin versions).

M-option

This adapter plate is for mounting to a 3" diameter bolt circle. Use two 4-40 x 1/4" screws (sold separately) to attach the E6D base to the plate. Comes attached when ordered with encoder.

View option:

SD-M-option.jpg

T-option

When mounting holes are not available, a pre-applied transfer adhesive (with peel-off backing) is available for stick-on mounting. Use the centering tool (sold separately) to slide the base into position. T-option specifies transfer adhesive on the standard mounting base.

View option:

S-T-option_0.jpg

D-T-option_0.jpg

View the PDF version of this document.

For Shafts Less Than Or Equal To 0.394" (10mm)

  • step1small_0.gif1. Base Mounting
    Secure the base to the mounting surface using two or three screws. If a centering tool is used, slip it over the shaft and into the center hole of the base. Tighten mounting screws. Remove centering tool.
  • step2small_0.gif
    2. Spacer Installation

    Place spacer tool on optic module as shown below.

  • step3small_0.gif
    3. Codewheel Installation

    Slip codewheel over shaft with mylar disk towards top until it bottoms out against the spacer tool. Tighten set screw with hex wrench provided while pressing down on hub.

  • step4asmall_0.gif
    4. Encoder Module Installation

    Slip optical module into position until two alignment pins slip into holes of module (thick side of module towards bottom). Secure with 4-40 x 1/2" screws (supplied).

    step4bsmall.gif
  • step5small_0.gif
    5. Cover Installation

    Place housing (cover) over assembly and secure with two 4-40 x 5/8" cover screws (supplied).

For Shafts Greater Than 0.394" (10mm):

  • step1large_0.gif
    1. Base Mounting

    Secure the base to the mounting surface using two or three screws. If a centering tool is used, slip it over the shaft and into the center hole of the base. Tighten mounting screws. Remove centering tool.

  • step2large_0.gif
    2. Spacer Installation

    Place spacer tool on optic module as shown below.

  • step3large_0.gif
    3. Codewheel Installation

    Slip codewheel over shaft with mylar disk towards top until it bottoms out against the spacer tool. Tighten set screw with hex wrench provided while pressing down on hub.

  • step4alarge_0.gif
    4. Encoder Module Installation

    Slip optical module into position until two alignment pins slip into holes of module (thick side of module towards bottom). Secure with 4-40 x 1/2" screws (supplied).

    step4blarge_0.gif
  • step5large_0.gif
    5. Cover Installation

    Place housing (cover) over assembly and secure with two 4-40 x 5/8" cover screws (supplied).

Please note:

  1. Shown using the Differential version
  2. These instructions are compatible for all versions of the E6.

1. Centering Tool

The centering tool is only included with the -3 packaging option. It has to be ordered separately for other packaging options.

Part #: CTOOL - (Shaft Diameter)
Description: This reusable tool provides a simple method for accurately centering the E6 base onto the shaft. It is recommended for the following situations:

  • When using mounting screws smaller than #4-40.
  • When the position of the mounting holes is in question.
  • When using the 3-hole mounting pattern.
  • When using the T-option transfer adhesive.

Instructions: When mounting encoder base, slide centering tool down shaft until it slips into centering hole of encoder base. Tighten mounting screws, then remove centering tool.

2. Hex Tool

Depending on the order packaging option, either a hex driver or hex wrench is included.

Part #: HEXD-050
Description: Hex driver, .050" flat-to-flat for #3-48 or #4-48 set screws. Only included with -B or -1 packaging options.

Part #: HEXW-050
Description: Hex wrench, .050" flat-to-flat for #3-48 or #4-48 set screws. Only included with -2 or -3 packaging options.

 

3. Spacer Tool

A spacer tool is included for all packaging options.

Part #: SPACER-265
Description: For shaft sizes < 0.472"

Part #: SPACER-555
Description: For shaft sizes 12mm to 1"

4. Screws

Screws for base mounting must be purchased separately. Screws for mounting the housing to the base are included.

Part #: SCREW-080-250-PH
Description: Pan Head, Cross Drive #0-80 UNF x 1/4"
Quantity Required for Mounting: 3 per encoder

Part #: SCREW-256-250-PH
Description: Pan Head, Cross Drive #2-56 UNC x 1/4"
Quantity Required for Mounting: 2 per encoder

Part #: SCREW-440-250-PH
Description: Pan Head, Cross Drive #4-40 UNC x 1/4"
Quantity Required for Mounting: 2 per encoder

Avago Direct Replacement:

US Digital's E6 encoder may now be used as a direct replacement for the following Avago encoders:

HEDL-6500, HEDL-6505, HEDL-6540, HEDL-6545.
HEDM-6500, HEDM-6505, HEDM-6540, HEDM-6545.
HEDS-6500, HEDS-6505, HEDS-6540, HEDS-6545.

Notes:

  • In order for the E6 to be fully compatible, CA-3921-2FT* must also be ordered separately.

*Custom cable lengths are available (standard length is 2ft).

Title Date Description Download
EM1 LED Die - PCN 10162/7/2013As part of US Digital's continual assurance of supply strategy, we have qualified additional sources for our LED die used in our EM1 encoder module, which in turn impacts all of the following products:

EM1, E2, E3, E5, E6, H1, H15, H3, H5, H6, HB5M, HB6M, HD25, PE, S1, S2, S5, S6, T5 and T6

The device specification will remain the same, i.e. there will be no change to form, fit or function of the product(s) as specified by US Digital. The appropriate quality and reliability testing has been performed on representative products to ensure normal parametric distribution, consistent with US Digital's quality and reliability standards.		Download

Product Description

Restriction of Hazardous Substances

The E6 Series rotary encoder has a molded polycarbonate which utilizes either a 5-pin or 10-pin finger-latching connector. This optical incremental encoder is designed to easily mount to and dismount from an existing shaft to provide digital feedback information.

The E6 Series is easy to add to existing applications and only consists of five main components; base, cover, hub/code wheel, optical encoder module and internal differential line driver (differential version only). 

The single-ended output version (S-option) is typically used with cables of 10 feet or less. For longer cable lengths, the differential output version (D-option) is recommended.

The base and cover are both constructed of a rugged 20% glass filled polycarbonate. Attachment of the base to a surface may be accomplished by utilizing one of several machine screw bolt circle options. Positioning of the base to the centerline of a shaft is ensured by use of a centering tool (sold separately). The cover is securely attached to the base with two 4-40 flat head screws to provide a resilient package protecting the internal components.

The internal components consist of a shatterproof mylar disk mounted to a precision machined aluminum hub and an encoder module. The module consists of a highly collimated solid state light source and monolithic phased array sensor, which together provide a system extremely tolerant to mechanical misalignments.

For differential versions: the internal differential line driver (26C31) can source and sink 20mA at TTL levels. The recommended receiver is industry standard 26C32. Maximum noise immunity is achieved when the differential receiver is terminated with a 150 Ω resistor in series with a .0047 μF capacitor placed across each differential pair. The capacitor simply conserves power; otherwise power consumption would increase by approximately 20mA per pair, or 60mA for 3 pairs.

A secure connection to the E6 Series encoder is made through a 5-pin (single-ended versions) or 10-pin (differential versions) finger-latching connector (sold separately). The mating connectors are available from US Digital with several cable options and lengths.

Related
Product Notes
  • Cables and connectors are not included and must be ordered separately.
  • US Digital warrants its products against defects in materials and workmanship for two years. See complete warranty for details.

Purchasing

Configure and Purchase

We recommend enabling Javascript when using the product configurator.

1. CPR
2. Bore
3. Index


4. Output




5. Cover



6. Base




7. Packaging




Product Part Number

This product requires configuration. Please supply the product options above.

Please configure your product for 3D model downloads.

Quantity Base Price
1 $89.80
5 $61.95
10 $54.93
50 $49.25
Over 50 Call for Quote
Quantity
Unit Price

$89.80

Subtotal

$89.80

For volume discounts, please use the above part number and contact us at:

sales@usdigital.com or

800.736.0194 (Toll Free)
360.260.2468 (Local)Call US Digital.

Best Sellers

Related Products & Accessories